• <button id="uem27"><tr id="uem27"><kbd id="uem27"></kbd></tr></button>

    <em id="uem27"><ruby id="uem27"><u id="uem27"></u></ruby></em>
    <dd id="uem27"><track id="uem27"></track></dd>
  • <th id="uem27"></th>
    <th id="uem27"></th>
    1. <li id="uem27"></li>

      歡迎訪問南京東頂新材料科技有限公司官網!

      南京東頂新材料科技有限公司

      運營中心: 江蘇省南京市溧水區開發區團山西路
      電話: 025-57201133
      郵箱:
      NJDD2003@163.com

      微信二維碼

      Copyright 2019?南京東頂新材料科技有限公司版權所有

      蘇ICP備18018706號-1       網站建設:中企動力南京

      Nanjing Dongding Chemical Co., Ltd.

      >
      產品詳細
      瀏覽量
      產品名稱

      H53-16高性能環氧厚漿型底漆

      概要信息
      所屬分類
      數量
      -
      +
      沒有此類產品
      產品描述

      產品說明 Description

      該涂料是雙組份環氧厚漿型涂料,固化劑分常溫固化和低溫固化兩種。固化劑A適用于5℃以上溫度條件下使用;固化劑B適用于-10℃~5℃溫度條件下使用。漆膜具有優異的防銹性和耐腐蝕性,優良的物理機械性能,耐磨、耐碰撞、耐海水、耐鹽霧性能佳,抗水滲透性好。

      This product is a two-component epoxy high build paint, with two kinds of curing agent: Ambient Curing (Curing Agent A) and Low-temperature Curing (Curing Agent B). Curing Agent A is suitable for the temperature above 5℃; Curing Agent B is used for the temperature of -10℃~5℃. The films have excellent resistance to rust and corrosion, good mechanical property, wear proof, crashworthiness, resistance to sea water, salt mist and water penetration.

       

      設計用途 Use

      用于船舶、橋梁、鋼結構作底漆。

      As primer for ships, bridges, and steel structures.

       

      物理參數 Physical Parameter

      顏色: 鉛紅色

      光澤: 無光

      理論涂布率:395g/m2,3.75 m2/L(以干膜150μm計,不含損耗)

      比重:約1.48

      干燥時間:23±2℃:表干≤4 h, 實干≤24h

      閃點:35℃

      貯存期:12個月

       

      Color: Lead Red

      Gloss: None

      Theoretical Spreading Rate: 395g/m2,3.75 m2/L (dry film 150μm, excluding loss)

      Specific Gravity: Approx. 1.48

      Drying Time: 23±2℃:Surface Dry≤4 h; Hard Dry≤24h

      Flash Point:35℃

      Storage Life: 12 months

       

      施工說明 

      混合配比 甲組份(漆料):乙組份(固化劑)=5:1

      熟化時間 23±2℃:20min(適用于固化劑A)

      0±2℃:20min(適用于固化劑B)

      適 用 期 23±2℃:4 h (適用于固化劑A)

      0±2℃:4 h (適用于固化劑B)

      施工方法 高壓無氣噴涂 有氣噴涂 手工刷涂、輥涂

      稀釋劑 環氧涂料稀釋劑

       

      Mixture Ratio: Component I (Paints):Component II (Curing Agent)= 5:1

      Maturing Time: 23±2℃:20min (for Curing Agent A)

      0±2℃:20min (for Curing Agent B)

      Pot Life: 23±2℃: 4h (for Curing Agent A)

      0±2℃:4 h (for Curing Agent B)

      Application Method: High Pressure Airless Spraying, Air Spraying, Manual Brush Coating and Roller Painting.

      Thinner: Epoxy Paint Thinner

      最大稀釋量 <5%

      Max. Usage of Thinner<5%

      噴孔:0.46-0.53mm

      Spray Orifice: 0.46-0.53mm

      噴出壓力:250Kg/c㎡

      Pressure When Spraying: 250Kg/c㎡

      工具清洗:環氧涂料稀釋劑

      Tool Cleaning: Epoxy Paint Thinner

      漆膜厚度 濕膜:265μm 干膜150μm

      Thickness of Film: Wet Film: 265μm; Dry Film: 150μm

      涂裝間隔

      Painting Interval

       

      底材溫度
      Temperature of Substrate Materials

      5℃

      20℃

      30℃

      最短
      Min. Time

      48h

      24h

      12h

      最長
      Max. Time

      3 months

       

      底材溫度
      Temperature of Substrate Materials

      -10℃

      0℃

      5℃

      最短
      Min. Time

      60h

      24h

      12h

      最長
      Max. Time

      3 months

       

      表面處理 Surface Treatment

      新鋼材表面經拋丸或噴砂處理,達到瑞典除銹標準Sa2.5級,若需要臨時保護的鋼材,可涂用適當的車間底漆,最后涂裝之間應將破損的車間底漆及污物徹底清除干凈。

      Surface of steels should be processed by shot blasting or sand blasting to achieve Sa2.5 of Sweden Rust Removal Standards. If temporary protection is required for steel, appropriate shop primer can be used for coating. The damaged shop primers and dirt should be completely cleared away before application of this product.

       

      施工條件 Application Conditions

      為避免水汽凝結,只能在干燥潔凈而溫度又高于露點3℃的面上施工,在狹窄空間內施工和干燥期內應大量通風。

      To prevent water vapor from condensation, the surface for coating should be dry and clean, ant its temperature should be 3℃ above the dew point. Forced ventilation must be provided during coating in confined space and drying period.

      前道配套涂料 各類車間底漆,也可直接涂于除銹 質量達Sa2.5級的鋼材表面上。

      Preceding Coats: Various kinds of shop primers. Also, it can be directly used on the steel surface where achieves Sa2.5 for derusting.

       

      包裝規格 Packing Specification Component

      甲組份20升容器裝20公斤,乙組份5升容器裝4公斤 。

      I: 20L Container, 20kg; Component II: 5L Container , 4Kg.

       

      備注 Notes

      可根據使用目的及部位修改漆膜厚度,但這會相應改變涂布率和干燥時間。

      Film thickness can be adjusted based on the intended use and the coating parts, but it will change spreading rate and drying time.

       

      注意事項 Attentions

        ˙被涂物表面必須除銹、除油、除灰塵及其它附著物。

        ˙若前道涂料涂裝時間過久,涂后道時應清除掉表面灰塵污物后再涂漆以保證層間附著力。

        ˙施工所用工具應清潔干燥,涂料不得混入水份及其它雜質,涂料現配現用,須4小時內用完。

        ˙漆膜未完全干燥固化之前,應采取保護措施,避免受到雨水或其它液體的沖洗和踐踏。

        ˙涂料存放于溫度較低通風干燥處,遠離熱源,避免日光直射,并隔絕火種。

        ˙The surface must be processed to remove rust, grease, dust and other attachments.

        ˙If the preceding coating has been done long time ago, dust and dirt should be cleared away first before the subsequent coating to guarantee the ply adhesion between coatings.

        ˙All tools for coating should be clean and dry. No water or other impurities are allowed to be mixing in the paints. The paints should be used within 4 hours after fresh mixing.

        ˙The film should be protected till its complete drying and curing to avoid washing or damage by water or other liquids.

        ˙The paints should be stored in low-temperature, dry and well-ventilated circumstances to keep away from heat, direct sun exposure and fire source.

       

      安全 Safety

      避免長期吸入溶劑蒸汽或漆霧,皮膚、眼睛不得接觸本品,在狹窄或空氣不流通處施工,必須提供強力通風,施工時應配防護用具。

      To avoid the long-term inhalation of solvent vapor or paint mists. To avoid contacts with skin and eyes. Forced ventilation must be provided when applying paints in confined space or stagnant air. Protective appliance is required during application.

       

      附注 Notes

      上述的干濕膜厚度都是指高壓無氣噴涂時的指標;

      本說明有關數據是在實驗室取得,實際產品可能與之略有不同;

      以上數據如有改變,以本公司最新說明書為準,恕不另行通知。

      All data in this description is obtained in laboratory and slight variation may occur during actual use. The above specification and description are subject to the change without notice.

       

      以上最終解釋權歸南京東頂化工有限公司所有 

      未找到相應參數組,請于后臺屬性模板中添加
      暫未實現,敬請期待
      暫未實現,敬請期待
      上一篇
      下一篇
      亚洲va无码一区二区三区观看_91精品久久久久久中文字幕无码_日本不卡无码二区三区_国产对白老熟女正在播放
    2. <button id="uem27"><tr id="uem27"><kbd id="uem27"></kbd></tr></button>

      <em id="uem27"><ruby id="uem27"><u id="uem27"></u></ruby></em>
      <dd id="uem27"><track id="uem27"></track></dd>
    3. <th id="uem27"></th>
      <th id="uem27"></th>
      1. <li id="uem27"></li>