• <button id="uem27"><tr id="uem27"><kbd id="uem27"></kbd></tr></button>

    <em id="uem27"><ruby id="uem27"><u id="uem27"></u></ruby></em>
    <dd id="uem27"><track id="uem27"></track></dd>
  • <th id="uem27"></th>
    <th id="uem27"></th>
    1. <li id="uem27"></li>

      歡迎訪問南京東頂新材料科技有限公司官網!

      南京東頂新材料科技有限公司

      運營中心: 江蘇省南京市溧水區開發區團山西路
      電話: 025-57201133
      郵箱:
      NJDD2003@163.com

      微信二維碼

      Copyright 2019?南京東頂新材料科技有限公司版權所有

      蘇ICP備18018706號-1       網站建設:中企動力南京

      Nanjing Dongding Chemical Co., Ltd.

      >
      產品詳細
      瀏覽量
      產品名稱

      S54-30聚氨酯耐油面漆

      概要信息
      數量
      -
      +
      沒有此類產品
      產品描述

      產品說明 Description

      由含羥基樹脂、多異氰酸酯預聚物、顏填料、助劑、溶劑等配制而成,分甲、乙雙組份包裝。漆膜耐原油、航空煤油、40#機油、120#汽油、煤油、柴油、苯等各種原油產品,且對油的質量無影響(膠質≤7mg/100mg)漆膜具有優異的防腐蝕性能和物理機械性能。

      It is made up of hydroxyl resin, polyisocyanate prepolymer, pigment and filler, additives, solvent etc.. Its film has good resistance to crude oil, 95/130 aviation gasoline, aviation kerosene, 40# engine oil, 120# gasoline, kerosene, benzene etc., but does not influence the oil qualities (colloid≤7mg/100mg). Also, its film has excellent corrosive protection, physical and mechanical properties.

       

      設計用途 Use

      油槽、油艙、油罐內表面作面漆。

      As finishing paint for the surfaces of oil sink, oil compartment and tanks.

       

      物理參數 Physical Parameter

      顏 色: 各色

      光 澤: 有光

      理論涂布率: 100g/m2,12.90 m2/1(以干膜35μm計,不含損耗)

      比 重: 約1.29

      干燥時間: 23±2℃:表干:2h,實干:24h

      完全固化: 23±2℃:7d

      閃 點: 甲組份25℃,乙組份30℃

      貯 存 期: 6個月

       

      Color: Various Colors

      Gloss: Glossy

      Theoretical Spreading Rate: 100g/m2,12.90 m2/1 (dry film35μm, excluding loss)

      Specific Gravity: Approx.1.29

      Drying Time: 23±2℃:Surface Dry:2 h; Hard Dry: 24h

      Fully Cured Time: 23±2℃:7 days

      Flash Point:Component I: 25℃; Component II: 30℃

      Storage Life: 6 months

       

      施工說明 Description of Application:

      混合配比 甲組份:乙組份=3:1

      Mixture Ratio: Component I:Component II= 3:1

      熟化時間 23±2℃:20分鐘

      Maturing Time: 23±2℃:20 minutes

      適 用 期 23±2℃:8小時

      Pot Life: 23±2℃:8h

      施工方法: 高壓無氣噴涂 有氣噴涂 手工刷涂、輥涂

      Application Method: High Pressure Airless Spraying, Air Spraying, Manual Brush Coating and Roller Painting.

      稀 釋 劑: 聚氨酯涂料稀釋劑

      Thinner: Polyurethane Paint Thinner

       

      高壓無氣噴涂
      High Pressure Airless Spraying

      有氣噴涂
      Air Spraying

      手工刷涂、輥涂
      Manual Brush Coating and Roller Painting

      5%

      10%

      3%

      0.4-0.5mm

      2.0-2.5mm

      -

      15-20MPa

      0.3-0.4MPa

      -

       

       

       

       

       

       

      最大稀釋量Max. Usage of Thinner

      噴 孔Spray Orifice

      噴出壓力Pressure When Spraying

      工具清洗 聚氨酯涂料稀釋劑

      Tool Cleaning: Polyurethane Paint Thinner

      漆膜厚度 濕膜:75μm 干膜35μm

      Film Thickness: Wet Film:75μm; Dry Film: 35μm

      涂裝間隔 0℃:最短3小時,最長48小時,25℃:最短2小時,最長24小時,35℃:最短1小時,最長16小時

      Painting Interval:

      0℃:Min.: 3 h; Max.: 48h;

      25℃:Min.: 2 h; Max.: 24 h;

      35℃:Min.: 1h; Max.: 16 h

       

      表面處理 Surface Treatment

      在前道涂層規定涂裝時間間隔內涂裝聚氨酯耐油面漆。

      Polyurethane Oil-resistant Finishing Paint should be coated within specific interval time of the preceding coat.

       

      施工條件 Application Conditions

      雙組份漆必須充分攪勻,按規定質量比配準,靜止20分鐘后施工。底材溫度須高于露點以上3℃;一般聚氨酯涂料施工氣溫最好在0-35℃之間,施工時注意天氣,溫度變化;雨、霧、雪天,相對濕度大于85%,夏季炎熱天氣時,在強烈陽光直射下均不可施工。

      Two components must be fully stirred and proportioned accurately as per the requirements. Wait for 20 minutes for application. The temperature of substrate materials should be 3℃ above the dew point. The best coating temperature is 0-35℃. Application should be stopped when relative humidity is more than 85% in raining foggy and snowing weather, or under direct and intense sunshine in hot summer days.

      前道配套涂料: 聚氨酯鐵紅防銹漆

      Preceding Coats: Iron-red Polyurethane Anti-rust Paint

      建議涂裝道數: 涂裝2-3道,干膜70-100微米

      Recommended Coating Number: 2-3 coatings, dry film 70-100μm.

       

      包裝規格 Packing Specification

      甲組份20升容器裝17公斤,乙組份10升容器裝5.7公斤 。

      Component I: 20L Container, 17kg; Component II: 10L Container, 5.7kg

       

      注意事項 Attentions

      1、該涂料最佳施工條件是溫度0-35℃,相對濕度≤85%,或被涂物表面應高于露點溫度3℃以上,在有雨、霧、雪和較大灰塵條件下,不可施工;

      2、該涂料可以用噴涂、刷涂、輥涂等方法,不同施工方法對涂料的粘度要求也不同,調整涂料的粘度應使用專用稀釋劑,嚴禁用水、香蕉水、醇和汽油等;

      3 、聚氨酯涂料屬“化學反應性”涂料,施工前必須充分攪拌均勻,按規定質量比配準并混合均勻。在25-35℃的氣溫下靜止20分鐘熟化后方可施工。若氣溫低于25℃時可適當延長熟化時間。經熟化后的涂料應在4-8小時內用完,以免膠結浪費;料使用后包裝桶蓋必須蓋子嚴密封,否則易受潮氣、醇、水的作用而變質;

      4、 本產品涂裝后漆膜在常溫下七天后完全固化,才能交付使用。

      1. The best coating temperature is 0-35℃ and relative humidity should be less than 85%, or the temperature of substrate materials should be 3℃ above the dew point. Application should be stopped during rainy, foggy, snowy and dusty weather.

      2. Spraying, brush coating and roller painting etc can be used for application of this product. But different method requires different viscosity, and it is necessary to use special thinner to adjust it. Water, banana oil, alcohol, petrol etc. are strictly prohibited.

      3. Polyurethane paint has chemical reactivity, so it must be fully and evenly stirred before use, and uniformly mixed as per the specific proportion. Then wait for 20 minutes for maturing at the temperature of 25℃-35℃. If the temperature is below 25℃, maturing time should be extended accordingly. The matured paint should be used up within 4-8 hours to avoid cementation.

      4. The cover of package must be tightly sealed after use to avoid deterioration caused by moisture, alcohol and water.

      5. Coating of this product is completed cured in 7 days at the normal temperature. Then it is acceptable for use.

       

      安全 Safety

      請注意包裝標簽上安全事項,此外還應遵守有關國家或當地政府規定的安全法規。避免長期吸入溶劑蒸汽或漆霧,皮膚、眼睛不得接觸本品,在狹窄或空氣不流通處施工,必須提供強力通風,施工時應配防護用具。

      Please notice safe attentions on the label. Also, national or local safety regulations should be followed. To avoid the long-term inhalation of solvent vapor or paint mists. To avoid contacts with skin and eyes. Forced ventilation must be provided when applying paints in confined space or stagnant air. Protective appliance is required during application.

       

      附注 Notes

      上述的干濕膜厚度都是指高壓無氣噴涂時的指標;

      本說明有關數據是在實驗室取得,實際產品可能與之略有不同;

      以上數據如有改變,以本公司最新說明書為準,恕不另行通知。

      The above index of dry and wet film thickness is under high pressure airless spraying.

      All data in this description is obtained in laboratory and slight variation may occur during actual use.

      The above specification and description are subject to the change without notice.

       

      以上最終解釋權歸南京東頂化工有限公司所有 

      未找到相應參數組,請于后臺屬性模板中添加
      暫未實現,敬請期待
      暫未實現,敬請期待
      上一篇
      下一篇
      亚洲va无码一区二区三区观看_91精品久久久久久中文字幕无码_日本不卡无码二区三区_国产对白老熟女正在播放
    2. <button id="uem27"><tr id="uem27"><kbd id="uem27"></kbd></tr></button>

      <em id="uem27"><ruby id="uem27"><u id="uem27"></u></ruby></em>
      <dd id="uem27"><track id="uem27"></track></dd>
    3. <th id="uem27"></th>
      <th id="uem27"></th>
      1. <li id="uem27"></li>